![\""Build](\"https:\/\/www.disneyexperience.com\/news\/wp-content\/uploads\/2020\/01\/xwbj14_01.jpg\")
<\/a><\/p>\nWoo-hoo! Three wings down, and only one more to go. I am more than ready to move on from these things. It would be much more tolerable if some of the X-Wing body was sprinkled here and there.<\/p>\n First, the two wing halves are joined, and the three metal support frames are screwed down with a lot of screws. Then, the extension wire for the laser cannon is routed through the wing.<\/p>\n <\/p>\n From the beginning, I have been tearing off the small, numbered tags on the wires. I figured that they were for packers to be able to identify which wires go in which box. But, I’ve noticed that the magazines have started referencing these numbers (early issues did not), which has me thinking that they may be important later on when they are plugged into the circuit board. So, I went through my model and numbered every plug using an black ultra fine point Sharpie<\/a>.<\/p>\n <\/p>\n It took some digging through online videos (early issues do not have the tags pictured), but I found the numbers, which are as follows:<\/p>\n With all of the wires now properly numbered, I attached the engine and routed the wire through the wing.<\/p>\n <\/p>\n Now, it’s time to assemble the troublesome engine. Not that it’s hard to do; it’s just fiddly. Plus, DeAgostini<\/em> is still incorrectly labeling the pipes. Note that in the corrected image, all of the parts and locations are mirrored on the actual engine.<\/p>\n The completed engine is secured inside of the wing.<\/p>\n Greeblies are assembled and attached to the wing, just under the thrust engine.<\/p>\n <\/p>\n The electronics are hidden with a large panel, and the screws are covered with small caps. The engine cover is glued to the engine, and two final greeblies are added to either side of the engine bay.<\/p>\n <\/p>\n The cannon is mounted to the end of the wing, connecting the wire to the existing extension wire. I used foil tape<\/a> to secure the wires and the keep them as flush with the wing as possible.<\/p>\n When I took the laser cannon assembly out of storage, I noticed that I had already painted it. I forgot that I did that, and it will create a slight problem when I paint the wing. I will have to carefully mask the whole laser cannon when I apply the gray primer<\/a>. Next time, I will paint everything at one time.<\/p>\n <\/p>\n I dry-fitted the wing cover, and I discovered that it was very loose. So, I glued it with Super Glue<\/a> and held it in place with clothes pins<\/a> and small binder clips<\/a>.<\/p>\n <\/p>\n With the wing completed, I filled in areas with epoxy putty. After the putty hardened, I sanded it flush with my homemade mini power sander<\/a>.<\/p>\n I keep the wings stored on a high shelf in my closet, and one of them decided to jump off. I wasn’t able to catch it; it fumbled in my finger tips. It hit the floor with a thud and a snap. The thrust engine had slightly twisted, but it popped right back into place with no damage. The laser cannon tube, however, snapped off from the main cannon housing. Fortunately, it was a clean break, and I was able to glue it back on. I tested the electronics to make sure that they still worked, and everything seems to be fine.<\/p>\n There was a teeny, tiny nick in the paint on the laser cannon, but I can fix later.<\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\nWorking on the Third Wing<\/h2>\n
<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n\n
\n
\n
\n
\n
<\/a><\/p>\n<\/a><\/p>\nAssembling the Engine<\/h2>\n
<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\nCompleting the Third Wing<\/h2>\n
<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\nDamage to the X-Wing<\/h2>\n